Trafficator Switch

Comfortable talk! email JCC UK Registrar. Technical Question? Try Service Bulletins or TechNotes or Tech Library or Parts book first. Note that you need to be a club member to view the Tech Library..

Paul Wilks' Javelin was shortlisted for Classic Car of the Year 2013.
Post Reply
Alan Stanley
Posts: 90
Joined: Fri Aug 25, 2006 9:25 am
Your interest in the forum: Nice Javelin, Concours Jupiter, half share in Jowett 10 slowly being restored. Third share in Bradford six light under restoration
Given Name: Alan
Location: Aucjkland, New Zealand
Contact:

Trafficator Switch

Post by Alan Stanley »

I am about to have a look at the clockwork traffictor switch this, it is a bit floppy, but before I pull it apart can anyone tell me what the thread is on the little screw that holds the knob on?
Also does it thread into the knob (arrow/jowett logo shaped)or into the shaft of the switch itself?
Leo Bolter
Posts: 367
Joined: Sat Feb 10, 2007 10:32 am
Your interest in the forum: Proud owner of:
1 x 1951 Jowett Jupiter
1 x 1952 LE Velocette
1 x 1952 Jowett Bradford
2 x 1982 Princess 2 litre
Location: R. D. 2, Palmerston North, 4472, New Zealand.

Post by Leo Bolter »

Hello Alan.

I have a spare (but not working) clockwork switch and a genuine black spear/arrow/logo knob, so I just when to the shed to check on it so I could, maybe, answer your questions.

1/ The shaft has a plain unthreaded 7/64" hole through it.

2/ The brass insert in the Bakerlite knob has had a thread in the outside part of the hole for the securing screw (where the screw enters), but unfortunately it's "gone" in the case of my knob . . . probably stripped. Incidentally, this hole in the knob does not pass beyond the metal shaft and into the brass on the other side of the shaft.

So, I'm sorry I'm not a great deal of help to you regarding the original thread and its size.

As it happens, to re-use my indicator knob would be a simple case of making a screw using any appropriate thread which incorporates a stepped down portion to accommodate the hole in the shaft. Or, as an alternative, the "far side" of the brass insert could be threaded for a screw with the outside diameter of 7/64" . . .

Cheers.
Leo.
R. Leo Bolter,
Palmerston North,
New Zealand.

JCC of NZ - Member No 0741.
JOAC - Member No 0161

Car: Jupiter (E1-SA-513-R)

Skype name = jupiter1951
Messenger name = r.l.bolter"at"massey.ac.nz
Leo Bolter
Posts: 367
Joined: Sat Feb 10, 2007 10:32 am
Your interest in the forum: Proud owner of:
1 x 1951 Jowett Jupiter
1 x 1952 LE Velocette
1 x 1952 Jowett Bradford
2 x 1982 Princess 2 litre
Location: R. D. 2, Palmerston North, 4472, New Zealand.

Clockwork Indicator Mechanism

Post by Leo Bolter »

Hi all.

When I have had a "floppy" knob in the past I have found in almost every case the clockwork actuating "hairpin" spring is broken. Occasionally though the spring is okay. I these cases I have found a good washing out of the dirt and dust accumulated over the years will revive it. A final rinse with a suitable CRC product has been used in the past, but maybe a new fangled Dry Lube like a Teflon aerosol spray might be better . . .

Does anyone else have a mechanism just needing a spring to make it work again?

Has anyone had success in hand making the springs, or are they procurable?

Leo.
R. Leo Bolter,
Palmerston North,
New Zealand.

JCC of NZ - Member No 0741.
JOAC - Member No 0161

Car: Jupiter (E1-SA-513-R)

Skype name = jupiter1951
Messenger name = r.l.bolter"at"massey.ac.nz
Tim Neville
Posts: 145
Joined: Sun Oct 29, 2006 5:32 pm
Location: North Devon
Contact:

Post by Tim Neville »

You might care to look at my Gallery album- Electrical - Trafficator switch.

TOPIC
Post Reply

Return to “Javelin”